Page 18 of 18

Re: Modelling bits for 3d printing

PostPosted: Tue Nov 29, 2016 3:16 am
by Malika
A bunch of my designs have been released by Vanguard Miniatures, allowing you to upgrade your Novan Warrior IFV (a very chunky possible Chimera proxy).

Warrior Turrets Upgrade Set B:
Image
(from left to right: right missile pod, left missile pod, pulse laser turret (with missile pod mounts), heavy laser cannon turret, bunker buster cannon, quad autocannons, medical front armour)
This set contains three sprues for upgrading the warrior IFV model with alternative weapon options. It will allow players to wield some of the rarer Warrior variants

3 x pulse laser turret with missile pod upgrade (Chimerro proxy)

3 x heavy anti tank laser cannon (APDS-6a Defender proxy)

3 x bunker buster (Chimedon proxy)

3 x quad autocannon (Chimerax proxy)

3 x hull MG position blanks with cross symbol (proxy for Samaritan medical transport)

£6.50

http://vanguardminiatures.co.uk/shop/wa ... ade-set-b/

Warrior Armour Upgrade Set A:
Image
This set contains spaced armour for upgrading the warrior model.

3 x hull side armour

3 x turret armour

Please note that the hull armour will fit on the Dragon and Support tank models too.

£5.00

http://vanguardminiatures.co.uk/shop/wa ... ade-set-a/


Warrior Armour Upgrade Set B:
Image
This set contains reactive armour for upgrading the warrior model.

3 x hull side armour

3 x turret armour

Please note that the hull armour will fit on the Dragon and Support tank models too.

£5.00

http://vanguardminiatures.co.uk/shop/wa ... ade-set-b/

Warrior Turrets Upgrade Set C:
Image
This set contains three sprues for upgrading the warrior IFV model with alternative weapon options.

Warriors of faith turrets.

3 x twin heavy machine guns

3 x twin heavy flamethrowers

3 x twin heavy microwave cannon

3 x hull MG position blanks with shield symbol

£5.00

http://vanguardminiatures.co.uk/shop/wa ... ade-set-c/

Re: Modelling bits for 3d printing

PostPosted: Sun Jan 22, 2017 12:14 am
by Malika
The Apocalypse Heavy Battle Tank I've designed for Vanguard Miniatures is as good as ready. All I need before shipping it off for printing is some final feedback.

So any suggestions, comments, etc. are more than welcome. :)

Image
Image

Re: Modelling bits for 3d printing

PostPosted: Wed Feb 01, 2017 6:18 am
by Islacrusez
That big dumb turret with the short derpy gun is so KV-2, and this is not strictly a bad thing.

On the other hand the flat top of the chassis is a little odd, doesn't really look like a tank. It just feels a little wrong. Might just be me? May also be the flat top combined with the raised turret ring. Could perhaps try dropping the turret ring a little (or sitting it near flush) and raising the engine deck behind the turret. Assuming you're interested in making drastic changes at this stage, of course.

Alternatively bring the turret ring down flush with the deck and then raise both the fighting compartment forward and engine deck aft up a little higher to give it a bit of a KV-5 silhouette.

Of note: Rear elevation looks good, front elevation feels a little top-heavy or tall, plan view is good (and has good lines front and rear), but the side elevation is particularly... not quite right.

Re: Modelling bits for 3d printing

PostPosted: Tue Mar 21, 2017 5:10 am
by Malika
My gun tower design has just been released! :D

Novan Sentinel Sentry Tower x 2:
Image
Image
Image
Image
The Sentinel class sentry tower is a modular armoured defence system seen across novan space. The system can be fully automated or semi automated with a single weapons operator. Designed to allow construction at various heights dependant on the local terrain or situation and with many different weapon load out options this is a versatile and rugged design that has seen great success during it’s time in service.

Set consists of two multi part sentry tower models with weapon options.

Tower height is: 55mm with turret in place.

£8.00

http://vanguardminiatures.co.uk/shop/no ... tower-x-2/

Re: Modelling bits for 3d printing

PostPosted: Sat Apr 08, 2017 10:39 pm
by Malika
The first batch of variants of the Centurion Battle Tank have been cast:
Image
Image
Image

Sniper tank:
Image

Siege tank:
Image

Autocannon tank:
Image

Plasma cannon tank:
Image

Laser cannon tank:
Image

Re: Modelling bits for 3d printing

PostPosted: Fri Jul 21, 2017 3:18 am
by Malika
Teaser...

Image